|
Back to Chevrolet Products
Corvette C4
(1984-1996)
|
|
|
 |
Premium Rotors
|
 |
SportStop Rotors
|
Better than stock rotors! Centric Premium rotors are identical in
dimensions and internal vane design to the factory originals. During assembly,
rotors are straddle cut for the most accurate machining, then double disc ground
for optimum parallelism, minimal runout, and near zero thickness variation.
A non-directional finish is applied for better initial pad bedding. All
surfaces, including the hat, are machined and non-swept surfaces are electrostatically coated with a durable, black finish
(unless noted otherwise below) for corrosion protection
and good looks. Finally, all rotors are computer mill balanced to
incredibly tight tolerances. You won't find a better replacement rotor
anywhere. Click here for more details.
(Note: Centric is the parent
company of StopTech and PowerSlot. All StopTech SportStop and Power Slot
rotors start as Centric Premium blanks and are machined in-house on computer
controlled milling machines.)
StopTech SportStop rotors are available for
many applications, offering all the advantages of Centric Premium rotors, with
the addition of slotting and/or drilling. Slotted rotors provide additional bite and maintain
consistent friction level over the life of your pads. These are ideal
for aggressive street and even road racing applications. Slotted and drilled
rotors offer even more bite and stunning looks, but should be used on the street and not for racing. If you prefer slotted
or slotted and drilled rotors and there is no pricing listed below, send an inquiry to
orders@zeckhausen.com and we can let you know if they are available.
Make sure you install them properly. See:
How to Properly Install Plain,
Slotted or Drilled Rotors
To obtain more information about any rotor, you
may click on the part number (if a link is present) to see more details,
including rotor drawings, recommended replacement thickness, critical
dimensions, and weight. Note: The term "floating" in the rotor
description does not mean two-piece, floating rotor. It is Centric's terminology for a
rotor that can be removed without also removing the car's wheel bearings or hubs.
To order, click here:
 and then locate your vehicle
along the left side of the on-line store page. Or, feel free to call us at
(800)222-8893 for help selecting the proper parts.
|
|
Rotors for 1988-1995 Corvette (except heavy
duty) |
 |
Plain Rotors |
|
Front
305mm x 20mm
1-piece vented rotors
Rear
305mm x 20mm
1-piece vented rotors
|
$72 Each
$54 Each |
120.62040
120.62041 |
|
 |
Slotted Rotors |
|
Front
305mm x 20mm
1-piece vented rotors
Rear
305mm x 20mm
1-piece vented rotors
|
$83 Each
$99 Each |
126.62040SL
126.62040SR
126.62041SL
126.62041SR |
|
Rotors for 1988-1996 Corvette (heavy duty) |
|
|
Plain Rotors |
|
Front
330mm x 28mm
1-piece vented rotors
Rear
305mm x 20mm
1-piece vented rotors
|
$80 Each
$68 Each |
120.62046
120.62047
120.62041 |
|
|
Slotted Rotors |
|
Front
330mm x 28mm
1-piece vented rotors
Rear
305mm x 20mm
1-piece vented rotors
|
$133 Each
$99 Each |
126.62046SL
126.62047SR
126.62041SL
126.62041SR |
|
High-Performance Brake
Pads |
|
If you want better brake pads
for the street, consider Axxis. Axxis pads are
manufactured by
Bendix Mintex (FMP Group Pty. Ltd.) in Australia. Formerly marketed under the
brand names PBR and Repco, they are now sold in the United States under the
Axxis name.
Axxis Brake pad performance
comparison charts
Instructions
for bedding in new brake pads
To order, click here:
and then locate your vehicle
along the left side of the on-line store page. Or, feel free to call us at
(800)222-8893 for help selecting the proper parts.
|
|
|
1984-1987 Corvette |
|
 |
Hawk HPS high performance street pads have
low dust, low noise, and low rotor wear. Slightly higher in friction
level than Hawk Ceramic pads with a similar MOT of
around 750°F. Not recommended for track use, as their
friction level falls off rapidly when the MOT is exceeded.
|
F-$98
R-$72
|
63-410-0294
63-410-0295
|
|
 |
Hawk HP PLUS high performance street pads have
moderate dust, moderate rotor wear, very high initial bite and similar MOT
to Hawk HPS of
around 750°F. They tend to be noisy, sometimes squealing under light
braking, although
proper bedding can help. Ideal for autocross.
Not recommended for track use, as their
friction level falls off rapidly when MOT is exceeded, just like the
Hawk HPS.
|
F-$126
R-$116
|
63-420-0294
63-420-0295
|
|
1988-1996 Corvette |
|
 |
Axxis ULT street pads
pads (formerly called Axxis Ultimate) use a Kevlar®
and ceramic formula for enhanced performance. They produce maximum
friction when cold, yet have tremendous fade resistance up to 932 °F. The
coefficient of friction is high enough to produce a noticeable reduction in
pedal effort. Fine for autocross or your first
track event, assuming street tires and a low horsepower car. This is
Zeckhausen Racing's favorite high performance street pad.
|
F-$122
R-$85 |
63-223-0412
63-223-0413 |
|
 |
Centric Posi Quiet Semi-Metallic pads
offer a high friction level across a wide temperature range. Very low dust, low noise
w/OE designed composite shims to reduce pad vibration and squeal. Easy on rotors.
Better performance than typical low-dust pads. Give up the dust
without giving up the performance.
|
F-$71
R-$51
|
63-104-0412
63-104-0413
|
|
|
Hawk HPS high performance street pads have
low dust, low noise, and low rotor wear. Slightly higher in friction
level than Hawk Ceramic pads with a similar MOT of
around 750°F. Not recommended for track use, as their
friction level falls off rapidly when the MOT is exceeded.
|
F-$113
R-$72
|
63-410-0412
63-410-0413
|
|
|
Hawk HP PLUS high performance street pads have
moderate dust, moderate rotor wear, very high initial bite and similar MOT
to Hawk HPS of
around 750°F. They tend to be noisy, sometimes squealing under light
braking, although
proper bedding can help. Ideal for autocross.
Not recommended for track use, as their
friction level falls off rapidly when MOT is exceeded, just like the
Hawk HPS.
|
F-$159
R-$116
|
63-420-0412
63-420-0413
|
|
 |
Hawk HT-10 Race pads have good
modulation and release characteristics, making them ideal for the
"weekend warrior." Moderate rotor wear, moderate dust, a stable torque
curve, above average bite, and a MOT of 1,400°F. Recommended for the
front of front-engine cars for casual track use, as well as for the rear of club
race and professional race cars.
|
F-$196
R-$162
|
63-490-0412
63-490-0413
|
|
|
Hawk DTC-60 is a member of the "Dynamic
Torque Control" race pad family with similar characteristics to DTC-70, but
less initial bite, slightly lower friction and an optimal temperature range
starting 100 degrees F lower. An ideal rear pad, when used with DTC-70
in front, for racers who prefer split friction levels. May be used in
front on lower horsepower cars or on cold days when DTC-70 can't be heated
sufficiently. Relatively low rotor and pad wear.
|
F-$223
R-$175
|
63-470-0412
63-470-0413
|
|
|
Hawk DTC-70 is the most serious member
of the "Dynamic Torque Control" race pad family, with an average level of friction among the highest
available and an incredibly linear pressure to torque relationship. The
result gives the driver an unparalleled ability to modulate
brake torque at the limit of tire adhesion, while keeping pedal effort low.
Relatively low rotor and pad wear for such an aggressive pad.
|
F-$232
R-$192
|
63-480-0412
63-480-0413
|
|
 |
PFC
01 Race pads have very high
average torque output, rising over its operating
temperature range, and a MOT of 2000°F. Excellent bite, low
rotor wear, and average pad wear. Novice drivers may find this pad
challenging to modulate. Pad of choice for top race teams and our
favorite due to overwhelming positive feedback and few complaints of judder. Frequently used in the front of front engine
cars with PFC 97 in the rear.
|
F-$227
|
63-660-0412
|
|
For front calipers only |
|
|
PFC
97 Race pads have medium to high
average torque output, a very flat torque output over its operating
temperature range and a MOT of 2000°F. Exceptionally low
pad and rotor wear and excellent modulation and release characteristics.
Popular for the front of front engine cars driven at
lapping and open track days. Often used on the rear of club and pro-level race cars
with PFC 01 in front.
|
R-$152
|
63-650-0413
|
|
For rear calipers only |
|
Performance, All-Season,
and Winter Tires |
|
Besides brakes, tires are the
most important component in determining stopping distance. It's literally
where the rubber meets the road. Selecting the right tire for your driving
conditions can make a tremendous difference. For example, if you live in
Florida or southern California and are driving on all-season tires, you are
leaving huge performance gains on the table! A good set of summer-only
performance tires can literally transform the handling and braking capabilities
of your car. In fact, if your goal is to minimize stopping distance,
you're better off going to Tire Rack's web site and buying tires first, before
spending any money here on better brakes!
For the best selection and
prices, use the Tire Decision Guide
by Tire Rack. Select the appropriate model year, then click the Go
button. You'll be asked a couple of questions which will help narrow down
your tire choices to the select few which most closely match your driving needs.
From Maximum Performance tires to All Season tires to Snow Tires, Tire Rack has
it all. The Tire Decision Guide takes the guesswork out of buying tires
for your car.
The Tire Decision Guide
 |
|
