Item #
|
Description
|
Part #
(for 32mm width calipers) |
Part #
(for 35mm width calipers) |
1
|
Bridge Bolt
|
40.6B0.6095
|
40.6B0.6097
|
2
|
Bridge Bolt Washer
|
40.220.0002
|
40.220.0002
|
3
|
STR-60 Bridge (Black Anodized)
|
32.639.N10R | 32.649.N10R |
4
|
TIME-SERT M6x1.0
|
40.160.0001
|
40.160.0001
|
5
|
Bleed Screw
|
41.000.0011
|
41.000.0011
|
6
|
Bleed Screw Cap
|
780.09450
|
780.09450
|
7
|
Crossover Tube
|
41.400.0105
|
41.400.0106
|
8
|
Abutment Block Kit
|
89.030.0005 | 89.030.0005 |
9
|
Body Bolt, M10x1.5, 110mm length
|
40.601.0110
|
40.601.0110
|
10
|
Body Bolt, M10x1.5, 100mm length
|
40.601.0100
|
40.601.0100
|
11
|
Body Bolt, M10x1.5, 90mm length
|
40.601.0090
|
40.601.0090
|
12
|
Body Bolt Washer, M10
|
40.220.0003
|
40.220.0003
|
16
|
Jet Nut (M10x1.5)
|
40.150.0000
|
40.150.0000
|
StopTech STR-60 Gen1-3 Trophy Sport calipers use application-specific piston sizing, with pistons ranging in diameter from 26mm to 46mm. These are typically staggered, with larger trailing pistons used. Thus, pistons are NOT all the same size. STR-60 Gen1-3 calipers use "short" pistons, 29.5mm in length. Pressure Seals (#13), Pistons (#14), and Dust Boots (#15) may be ordered here: Rebuild Parts
Brake pads may be ordered here: STR-60 Pads
All other STR-60 hardware is listed below.
StopTech abutment plate kit. Contains four abutment blocks, four stainless steel abutment plates (two with pad tensioning kinks), eight M5…
Banjo bolt - M10x1.0 threads, 20mm shank, 29.5mm overall length…
Rubber bleed screw cap for StopTech brake calipers. Sold individually.…
Replacement bleed screw for StopTech brake calipers, including ST-60, ST-43, ST-42, ST-41, ST-40, ST-22. Overall length 29mm, base of hex…
Adapt your vehicle's pad wear monitoring system to work with StopTech big brake kit calipers. Order the same quantity as…
Caliper stiffening bridge for StopTech STR-60 caliper. Also order two pad retaining springs p/n 42.100.0080 and spring screw set p/n…
Caliper stiffening bridge for StopTech STR-60 caliper. Also order two pad retaining springs p/n 42.100.0080 and spring screw set p/n…
StopTech crossover tube for Gen2 through Gen4 ST-40, ST-45, and ST-60 calipers - 32mm thick rotors. 131.5mm between hole centers.…
StopTech crossover tube for ST-40, ST-45, and ST-60 calipers - 35mm thick rotors. 134.5mm between hole centers. These will not…
10mm copper crush washers for StopTech calipers. 10mm ID, 15mm OD, 1.25mm Thickness. Quantity 4…
Washers (QTY 2) for StopTech Jet nuts. Also used with StopTech ST-22 and ST-45 caliper mounting bolts and caliper body…
Jet Nut, 7/16x20 Self Locking, Gold Cad plated. Used to attach StopTech caliper to mounting bracket (Pair)…
Pad retaining spring for StopTech ST-60/STR-60 caliper bridge - 2 springs required per bridge…
M10x1.5x110mm caliper body through-bolt for StopTech, Dacromet coated, sold individually. Special order…